Massive Audio M8S User's Guide download pdf (Page 8)

M8 REAR PANEL FEATURES

9. CHANNEL INPUT SWITCH - (Eight, four-position switches) Set these switches to select the input to each channel. These

switches allow multiple audio sources to be connected and played simultaneously. LINE IN feeds audio only to it’s dedicated

channel. BUS L/BUS R will set a channel’s input to the source connected to BUS IN Left or Right. AUX L/AUX R will set a chan-

nel’s input to the source connected to AUX IN Left/Right.

LINE - Set the switch to LINE to select a source connected to that channel’s Line IN. Line IN conguration can be mono

(1-8) or stereo (1/2, 3/4, 5/6, 7/8) or bridged stereo pair (1+2/3+4, 5+6/7+8) inputs.

BUS L/BUS R - Set the switch to BUS L/BUS R to set a channel input to the source connected to BUS IN Left/Right.

To select a mono source connected to BUS IN Left, set the switch to BUS L. To select a mono source connected to BUS IN

Right, set the switch to BUS R.

To select a stereo source connected to the BUS IN, set the switches for channel pair (1/2, 3/4, 5/6, 7/8) to BUS L. (1, 3, 5, 7)

and BUS R (2, 4, 6, 8).

AUX L/AUX R - Set the switch to

AUX L/AUX R to set a channel input to the source connected to AUX IN Left/Right.

To select a mono source connected to AUX IN Left, set the switches for odd number channels (1, 3, 5, 7) to AUX L. To

select a mono source connected to AUX IN Right, set the switches for even number channels (2, 4, 6, 8) to AUX R.

Note: A mono source connected to AUX IN Left can only be selected b

y odd number channels. A mono source connected

to AUX IN Right can only be selected by even number channels. To distribute a mono source to eight channels, use BUS

IN.

To select a stereo source connected to the AUX IN, set the switches for channel pair (1/2, 3/4, 5/6, 7/8) to AUX L (1, 3, 5, 7)

and AUX R (2, 4, 6, 8).

10. FUSE - Replaceable T10AL/250V fuse.

11. AC INPUT - Connect to the included IEC 2-prong AC Power Cord. After all connections have been made and conrmed, plug

the power cord into an unswitched 110V AC Outlet to power the M8. Contact Procient Audio Systems for a proper replace -

ment should the AC Power Cord be damaged or misplaced.

12. SPEAKER TERMINALS - (Sixteen ve way binding posts) Connect to the appropriate speaker + and - terminals as congured

for normal or bridged modes. The M8 can be congured for eight mono, four normal power stereo outputs, two bridged high

power stereo outputs or a combination of mono, stereo and high power bridged outputs.

Note: Regardless of conguration, be sure to conrm switch settings and connections prior to powering up the M8. Improper

bridged switch settings and connections can cause severe damage to the M8 and

speakers. The Procient Warranty does not

cover this type of damage.

13. 12V DC CONTROL OUT - (One 3.5mm mini jack) Connect to the 12V DC Control Input on a device that is to be synced to M8

ON/OFF status. When the M8 turns ON, (Manual, Auto ON or Trigger) the 12V DC Control Out will output 12 V DC that can be

used to activate a DC voltage controlled device. When the M8 turns OFF (Manual, Auto or Trigger) voltage will be cut to the

Control Out and the controlled device will turn OFF. POLARITY: TIP = +12V; SLEEVE = GND.

14. POWER MODE/TRIGGER IN - (One, three position switch; One, 2.1mm coaxial jack) Congure this switch and Trigger jack to

set the power ON/OFF mode for the M8. The M8 can be turned ON/OFF in one of three ways: manually pressing the ON/OFF

button on the Front Panel; Auto ON (audio sense) which will turn the amp ON when an audio signal is present on any input

and turn it OFF when no audio signal has been sensed for 5 minutes; Voltage Trigger will turn the M8 ON/OFF w

ith the pres-

ence or absence of 3-30V AC/DC on the Trigger IN jack.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 31 32

No comments

Massive Audio M8S User's Guide Page 8